桥梁防震橡胶垫块生产厂家

橡胶止水带是用来进行止水的;钢边橡胶止水带在橡胶中间焊止水片外面近模板处焊定位片,对于钢边橡胶止水带要求满焊,定位片只要牢固就可以了,定位片距模板要有一到二公分的距离,这之间加塑料或者木质垫片。拆模后剔出,割掉螺杆后用微膨胀砂浆填平。还有种国内少见 就是用短一点的螺杆外加连接螺杆,拆模后可以很方便的拆下。
The rubber sealing strip is used for sealing; steel edged rubber water stop outside the middle rubber waterstop welding near the template at the welding positioning piece, the steel edged rubber water stop full welding requirements, as long as the firm positioning piece can, positioning distance template to one to two cm distance, plastic or wooden pads plus this. After stripping out, cut off after the mortar filled with micro expansion screw. There are kinds of domestic rare connection screw rod is a little shorter, after stripping can be easily disassembled.
橡胶止水带是在混凝土浇注过程中部分或全部浇注埋进混凝土中。在浇埋混凝土以前先要使其在界面部位保持平展，接头部分粘接紧固，再以适当的力充分浇捣，震荡混凝土来定位止水带，使其与混凝土良好的结合，以免影响止水效果。
The rubber water stop belt is partially or completely poured into the concrete during the concrete pouring process. Before pouring the concrete, it is necessary to keep it at the interface part. The joints are fastened and fastened. Then the concrete is fully poured and tamper with the appropriate force. The concrete is positioned by the shock concrete to make the water stop band well combined with the concrete so as not to affect the sealing effect.

桥梁防震橡胶垫块生产厂家
橡胶止水带施工注意事项在施工过程中，由于混凝土中有许多尖角的石和锐利的钢筋，所以在浇捣和定位止水带时，应注意浇捣的冲击力，以免由于力量过大而刺破橡胶止水带。如果发现有破裂现象应及时修补，否则在接缝变形和受水压时橡胶止水带抵抗外力的能力就会大幅度降低。固定止水带时，只能在止水带的允许部位上穿孔打洞，不得损坏本体的部分。在定位橡胶止水带时，一定要使其在界面部
In the process of construction, because there are many sharp corners and sharp reinforcing bars in the concrete, the impact force should be paid attention to when pouring and locating the sealing belt, so as not to pierce the rubber water stop because of too much power. If the rupture is found to be repaired in time, the capacity of the rubber belt to resist external force will be greatly reduced when the joints are deformed and subjected to water pressure. When the sealing zone is fixed, the hole can only be perforated on the allowed part of the water stop belt, and the part of the body can not be damaged. When locating a rubber sealing belt, make sure that it is at the interface
位保持平展，更不能让止水带翻滚、扭结，如发现有扭结不展现象应及时进行调整在浇注固定止水带时，应防止止水带偏移，以免单侧缩短，影响止水效果。在混凝土浇捣时还必须充分震荡，以免止水带和混凝土结合不良而影响止水效果。止水带接头必须粘接良好，如施工现场条件具备，可采用热硫化连接的方法。不加任何处理的所谓“搭接”是不允许的。
The position is kept flat, and it can not even make the water stop roll and twist. If there is a kink and no appearance, it should be adjusted in time. When the fixed watertight belt is placed, the waterstop should be prevented from being offset, so as to avoid the shortening on one side and affect the sealing effect. When the concrete is poured, it must also be fully concussion, so as to avoid the bad combination of water and concrete, which will affect the effect of water stop. The joint of the water stop belt must be well bonded, such as the condition of the construction site, and the method of hot vulcanization can be used. The so-called "lap" without any treatment is not allowed.

桥梁防震橡胶垫块生产厂家
橡胶止水带施工与安装方法的正确性是使用橡胶止水带的关键所在，我们知道橡胶止水带是在混凝土浇注过程中部分或全部浇埋在混凝土中。由于混凝土中有许多尖角的石子和锐利的钢筋，所以在止水带定位和混凝土浇捣过程中，应注意安装定位方法和浇捣压力，以避免止水带被刺破。由于塑料和橡胶的抗断撕裂强度比拉伸强度低3-5倍，所以如果产品被刺破将会大幅度降低产品抵抗外力的能力，故在施工中要格外注意。
The correctness of the construction and installation of rubber sealing belt is the key to the use of rubber water stop. We know that the rubber sealing belt is partially or entirely embedded in concrete during the pouring process. Because there are many sharp stones and sharp reinforcing bars in concrete, so we should pay attention to installing location method and pouring pressure in the process of water stop location and concrete pouring and tamping, so as to prevent the waterstop being punctured. Because the tensile tear strength of plastic and rubber is 3-5 times lower than that of tensile strength, if the product is punctured, it will greatly reduce the ability of products to resist external force, so we should pay special attention in construction.